《お取り寄せ商品》WiFi Shield V3 For Arduino PCB Antenna (802.11b/g/n)--販売終了

本商品はお取り寄せ商品（輸入代行）です。他の商品と同時にご注文いただいた場合、全ての商品が入荷してから出荷します。お急ぎの商品と一緒にご注文なさらないよう、ご注意下さい。この商品のお買い求めの手続きを完了し、代金のお支払いをいただいてから、お取り寄せを行います（請求書払いのご契約をいただいている場合には、もちろんこの契約が優先です）。納期は仕入先に在庫がある場合、通常1.5～2ヶ月ほどです。発注は定期的に、まとめて行いますので、お取り寄せ依頼時に仕入先在庫があっても、当社発注時に仕入先在庫がない場合、納期は未定となります。

本商品は電気用品安全法、電波法、その他日本の法律に準拠していない可能性があります。本商品のお取り寄せは輸入代行サービスです。お取り寄せのご案内をご確認の上、ご注文ください。当社はお取り寄せ品に関して一切の責任を持ちません。お客様自身で適法かつ安全にご利用いただけることを充分にご確認いただき、お取り寄せをご依頼ください。また商品が輸入できないなどの問題が発生した場合、ご注文をキャンセルする場合があります。

Introduction

DFRobot WiFi Shield, is part of our wireless family product. This WIFI Shield V3 supports AP + STA dual mode, and is extremely easy to connect to a home router network. You only need a mobile phone or Pad to log in the AP network of this module (similar way with some router configuration tool). After logging in the module and set the Wireless name, it is ready to connect the WIFI network (No AT command setup required, which is often very complex).

This module uses dynamic power management to achieve low power consumption capability (standby: <80uA; normal mode average: 8mA; peak: 200mA). This is especially useful in prototyping which not only demands low power consumption, but also requires a standby mode. The module provides UART(TTL) to IEEE802.11b/g/n wireless communication. IEEE802.11n is a newest wireless transmission protocol which features higher transmission speed, wider coverage, stronger compatibility and much more reliability. Currently many wireless electronic equipment manufacturers have been applying this standard (IEEE802.11n) to a large number of products. With this WIFI Shield, any device with UART can easily set up a wireless network and achieve remote management and controlling. This is an excellent choice for those with wireless communication compatibility issue.

Specification

• Working voltage: 5V
• Frequency range: 2.4 - 2.497GHz
• Output power: 16dBm
• Transmission rate: 54Mbps - 1Mbps
• Transmission distance: <150M(590.55")
• Size: 55 × 53 × 11mm(2.16x2.09x0.43")
• Weight: 40g
• Support IEEE 802.11b/g/n
• Support AP, Client, Gateway and UART to WLAN mode and so on
• Support DHCP, automatic access to IP; Support allocating IP to slave device in AP mode
• Support network protocol: TCP/ UDP/ ARP/ ICMP/ HTTP/ DNS/ DHCP
• Optional working modes: TCP Server/ TCP Client/ UDP; Support up to 32 Client in TCP Server mode
• Support most of WIFI encryption algorithm: WEP/ WAP-PSK/ WAP2-PSK/ WAPI; Type of encryption: WEP64/ WEP128/ TKIP/AES
• Support transparent UART/protocol data transmission mode; Up to 1M cache space; Highest baud rate: 460800bps
• Support UART(TTL) to wireless applications
• Drag down the level of the Reload IO pin for one sencod, you can restore factory settings. So do not worry about the wrong settings.
• Support running in AP mode and the node (Station) mode;The real hardware AP, so Android can directly access it.
• Provide AT command configuration
• Provide the friendly web configuration page, and can be configured by webpage
• Serial frame delay and the amount of data can be set.
• Support routing/bridge mode network architecture
• Designed by standard Arduino stack, and can be easily put on the standard Arduino, MEGA, Romeo board or shield

Documents

• WiKi Doc
• Schematic
• User Manual (Included AT commend)
• WiFi Firmware (V1.0.5)

ShippingList

• WIFI Shield V3(PCB Antenna) ×1

Projects

• Discussion and extended info ( Forum )

上記製品説明はDFRobotのサイトのHTMLをそのまま転載しております。当社サイトでの表示確認をしていないため表現が正しくない部分が残っております。また情報の更新が遅れている可能性もありますので、製品情報についてはDFRobot社のサイトをご確認ください。当社コード番号"DFROBOT-"以降のコードを製品検索に利用できます。たとえば、DFROBOT-DFR0470-ENTは、”DFR0470-ENT”とDFRobot社のサイトにて検索ください。

商品コード: DFROBOT-TEL0078